1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 2018

T3-Prosjekter (Caravelle/Transporter 1980-1991/Syncro -92)
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Hvordan skifte registerreim på en AAZ :D
Ser nå i etterkant at videoen ikke ble helt bra, men det går ann å forstå hvordan fremgangsmåten er.

https://www.youtube.com/watch?v=LDhSMxwZP2c
Last edited by Italjohn on 08 Sep 2021, 12:12, edited 2 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Fikk delene fra Brickwerks i dag.
Jeg forstår ikke helt hvordan denne skal monteres, så jeg har sendt en mail til de angående dette.
Denne simringen er laget av et annet materiale enn den original (PTFE), konstruksjonen er også annerledes.

Image
Image

Vel, etter litt reseach på nettet, fant jeg denne videoen.
Må visst ha et spesial verktøy for å montere denne ringen.
OBS: Gjelder en annen type ring.

https://www.youtube.com/watch?v=Pkh8_GlQJu4

Tror jeg fant svaret her 4:15 ute i filmen.

https://www.youtube.com/watch?v=Tzn4OVPSWrU

Installation of PTFE Oil Seals
TIP FROM THE EXPERTS
Only remove PTFE oil seals from their protective packaging immediately before installation, to protect them from dust and other contamination.
The sealing lip of PTFE oil seals is protected by a plastic sleeve, which can normally be used as an assembly aid.
Therefore, the sleeve should remain in place until the seal has been installed.
If the seal is to be installed without the sleeve, use the special tool provided by the manufacturer.
Both the PTFE sealing lip and the shaft surface must be completely dry. Do not use any grease or oil.
The shaft may not exhibit any sharp-edged chamfers – if necessary, have the edges removed by an engine expert.
The shaft surface must be in a perfect condition – also here, possible damage must be repaired by an expert.
Position the assembly sleeve with the PTFE oil seal on the shaft.
Make sure that the sealing ring is aligned correctly – the sleeve must be located so that the seal can be pushed onto the shaft smoothly.
Push the sealing ring onto the shaft with an even motion.
When replacing, the PTFE lip of the new seal should not run in the same position as the old one.
You can now remove the assembly sleeve.
Do not start the engine sooner than four hours after installation – this permits the new sealing lip to adapt perfectly to the shaft.

When installing integrated oil seals, please note that it is usually necessary to slightly loosen the oil pan to enable the radial seal to be pushed onto the crankshaft.
Image

Damaged PTFE Sealing Lip
The most frequent cause for failure is damage to the PTFE sealing lip during assembly.
If the seal is installed without the help of a sleeve or special tool, and is shifted or even turned inside out, reliable sealing will hardly be possible.
Similarly, the use of oil or grease – as with classical oil sealing rings – will result in total failure of the PTFE oil seal immediately after installation.
Last edited by Italjohn on 08 Sep 2021, 12:13, edited 6 times in total.
Needforspace
-
-
Posts: 4333
Joined: 07 Jun 2005, 14:19
Car: VW E-Golf -16, T3 Syncro -89, VW Crafter LWB -14
Phone: 41tonull5391
Location: Måløy

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Needforspace »

Virker litt unødvendig vanskelig, jeg byttet bare ringen uten at det har gitt meg noen problemer. Du trenger forøvrig ikke noe spesialverktøy, det hvite plast senteret utgjør dette verktøyet. Gudd løkk. :wink:
VW E-Golf -16
Caravelle C T3 -89 Syncro 1,9 AAZ m/to sperrer og decoupler
VW Crafter LWB -14

PM konto full, bruk mail: subcool.joa krøll gmail.com
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Needforspace wrote:Virker litt unødvendig vanskelig, jeg byttet bare ringen uten at det har gitt meg noen problemer. Du trenger forøvrig ikke noe spesialverktøy, det hvite plast senteret utgjør dette verktøyet. Gudd løkk. :wink:
Jo takk, gudd løkk kan jeg vel trenge her :D
Ser i video nr2 at han bare presser ringen på plass og den hvite plastringen faller ut av seg selv.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Fant feilen som forårsaket oljelekkasjen :o
Rart jeg ikke merket dette når jeg monterte den!
Ny simring montert, og lekkasjen er nå borte :D

Image
Image

Byttet noe gummigreier ved girkassen i dag.

https://www.youtube.com/watch?v=FssYLKW ... e=youtu.be
Last edited by Italjohn on 08 Sep 2021, 12:13, edited 2 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Da var endelig riktig størrelse Dieselvarmer kommet i hus.

Image

Samme tollbehandling som den første jeg fikk :lol:
Image
Last edited by Italjohn on 19 Mar 2019, 11:35, edited 1 time in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Sammenligningsfilm mellom 2kw og 5kw.

[youtube]https://www.youtube.com/watch?v=mivEyt3BwTc[/youtube]
[media][/media]
Last edited by Italjohn on 08 Sep 2021, 12:14, edited 1 time in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Westfalia edition :D
Ble langt ifra bra, men bra nok

Image
Image
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Snubblet over denne i dag :D
Byttet den til meg mot 2 brett med Colabokser 8)

Image

Det morsomme er at denne fra Kina er oppgitt til 1500 watt og den store (og tunge) fra Victron bare er 800 watt.
Den fra Kina er riktig nok en Modify sine wave, og den fra Victron er en Pure sine wave :D

Image
Last edited by Italjohn on 17 Apr 2019, 11:32, edited 1 time in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

"W" utgang laget på min 120 ampers dynamo.
Om jeg får den til å passe i bilen er en annen sak.
NB: Pass på at du lodder deg innpå en vikling og ikke en diode!
Dioder gjenkjennes igjen på at de er runde og presset inn i huset.

Image
Image
Image
Image
Last edited by Italjohn on 30 Sep 2020, 19:39, edited 1 time in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Monterte mine flott beauty ringer fra http://www.brickwerks.co.uk i dag.
Synes selv de ser riktig så flotte ut :D

Image

[youtube]https://www.youtube.com/watch?v=OWjvhJS-Wqs&t[/youtube]
Last edited by Italjohn on 08 Mar 2023, 15:48, edited 3 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, bygges om til AAZ i 2018

Post by Italjohn »

Ny gassalarm :D

Image
Image
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

I dag fikk jeg endelig startet på lydoppsettet mitt.

Image

Nede på døren kan en se det gamle hullet fra de små 4" Pioneer høyttalerne som stod der da jeg kjøpte bilen.
Image
Image

Brukte litt tape for å forme plasten som en kule over høyttalerne. Da skulle de tåle en regnskur eller to.
Image
Last edited by Italjohn on 25 May 2019, 15:25, edited 1 time in total.
Buss Marius
-
-
Posts: 1917
Joined: 04 Jan 2011, 14:49
Car: 87 Karmann LT 89 T3 Syncro Camper 2000 T4 Buss nr1
Phone: 92023467
Location: Lommedalen i Bærum

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Buss Marius »

Hvor mye har du igjen av nyttelasten nå da?
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Buss Marius wrote:Hvor mye har du igjen av nyttelasten nå da?
Tja ikke godt å si, men har en god følelse så langt :D

Byttet girolje til Biltema sin mineral olje 80W-90 LS, og virkningen kom umiddelbart.
Ingen skraping i 2.gear lengre, girene er helt synkrone noe de ikke var med den syntetiske oljen. :D
Så da er det vel noe i dette at syntetisk olje blir for glatt til at synkronringene får tak.

ImageImage
ImageImage
Last edited by Italjohn on 25 May 2019, 15:35, edited 3 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Tekniskedata på AAS girkasse (og andre typer)

Image
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Fikk koblet til styringspinne på tenningslås, slik at radio slår seg på når en setter nøkkel inni tenningslås (trenger ikke å vri nøkkel rundt)
Tenningspinnen styrer et rele slik at radio blir drevet av batteriet under setet.

https://www.youtube.com/watch?v=C5MeILjfAvc
Last edited by Italjohn on 06 Jan 2022, 12:46, edited 5 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Mine nye kjøkkenvindu og luftevindu venstre bak samt ventil til skyvedør og vinduer fremme.
Ikke fått montert vinduene enda, men det er ikke lenge til nå :D
Kjøpt hos http://www.serial-kombi.com

Image
Image
Image
Last edited by Italjohn on 30 Aug 2019, 11:03, edited 1 time in total.
Buss Marius
-
-
Posts: 1917
Joined: 04 Jan 2011, 14:49
Car: 87 Karmann LT 89 T3 Syncro Camper 2000 T4 Buss nr1
Phone: 92023467
Location: Lommedalen i Bærum

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Buss Marius »

Jeg har aldri kjøpt noe fra Serial-Combi. er de kjappe å ha med å gjøre? Hva kostet vinduene, med forsendelse?
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

De har en fantastisk service. Jeg fikk mine sendt til mitt hotell i Tyskland, og klarte å "snakke" til meg gratis frakt.
Philipp er mannen jeg hadde mailkontakt med der nede. Fikk tracking sendt på mail og alt var bare fryd og gammen.
Litt tungvindt betaling, da jeg måtte overføre pengene i nettbanken.

Venstre skyvevind (lang versjon1080x428mm) Reference 253847711
https://www.serial-kombi.com/en-GB/tran ... 92-n316557
Image

Høyre skyvevindu bak Reference 253847766
https://www.serial-kombi.com/en-GB/tran ... 41-n317979
Bilde fra Serial-kombi.
Image
Last edited by Italjohn on 08 Mar 2023, 12:54, edited 5 times in total.
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Soting av vinduer :D
Brukte Biltema sin varmeavvisende solfilm Art.nr. 39-776

Tekst fra Biltema:
Varmeavvisende solfilm som reflekterer bort opptil 80 % av varmen fra solen og avviser skadelig UV-stråling.
Holder bilen kjølig om sommeren og varm om vinteren.

Image
Image
Runner
-
-
Posts: 150
Joined: 24 Oct 2014, 11:28
Car: T3 1989 JX
Phone: 9+7-7-2-2-2-1+2
Location: Nordreisa

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Runner »

Litt vel sært å bytte ut vinduer på huset med T3 vinduer, men jeg forstår deg. Blir bra!
ducce999s
-
-
Posts: 5757
Joined: 07 Aug 2009, 01:52
Phone: 9-1-6-0-9-7-9-0
Location: Rjukan / Oslo
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by ducce999s »

Runner wrote:Litt vel sært å bytte ut vinduer på huset med T3 vinduer, men jeg forstår deg. Blir bra!
[emoji23][emoji23][emoji23][emoji23]

Sent fra min H9436 via Tapatalk
SYNCRO1,9TD,SIKASYNCRO2,1,JOKER3 2,1++
TL 1600 Fastback -69
Opel GT 1900 -69
"I'm afraid that, when I die, my wife will sell my car parts for what I told her that I paid for them."
Paul G
Italjohn
-
-
Posts: 955
Joined: 26 Sep 2016, 12:23
Car: T3 1986 1,9 AAZ (TDK) AAS sperrediff
Phone: 93211119
Location: Molde
Contact:

Re: 1986 Hightop Westfalia 1,6 TD, byttet motor til AAZ i 20

Post by Italjohn »

Kjøpt meg en Sharan :D
AFN 1,9 110hp

Image
Image
Image
Post Reply